introduction – Parts of sitar
The sitar is comprised of various parts handmade and embedded/fixed onto a log of wood and a piece of sometimes a pumpkin/gourd attached to that wood to create the resonation that creates the sitar’s marvellous sound. For a detailed explanation of the sitar strings and their location, see How many strings does a Sitar have.
It comprises the main body of sitar. Made from the shell of dried ash-gourd or kaddu. It is fragile and subject to be taken full care of, as it is hollow inside.
Dand/ Dandi (Fret/fingerboard)
Made from teak or tun wood it is hollow from inside. Frets are tied on the dand. Made from single piece of wood, it can twist over a period of time. So, whether extremities or neglect of resting position of sitar may lead to its damage.
A neck shaped piece which serves as a joint between toomba and dand. Gullu is usually decorated with engraved floral designs which adds an extra beauty to sitar.
Tabli/The Face Plate
Traditionally made from teak or toonwood, this is a thick piece made to cover toomba. This combined with toomba serves as a resonator. The quality of sound of sitar to a major extent depends on the Tabli and the quality of wood used in its making. It is a very crucial part of the body of the sitar as ghoraj is placed on it.
Bridge is made from dead animal bone, ebony, or polyoxymethylene plastic (Delrin). This is a table like structure which has feet of wood on two sides and rests on the Tabli.
THERE ARE TWO TYPES OF SITAR BRIDGES
- Bada Ghoraj (Big Bridge) – it serves as stool to let the strings pass over it. All the six or seven main strings pass over it to reach the pegs (Khoonti).
- Chota Ghoraj (Small Bridge) – has the same purpose as of the big bridge. It lets the sympathetic strings to pass over it to be tied to Khoonti or Pegs.
A comb like structure on the posterior part of the bridge from where all the strings get a passage towards both the ends of sitar. The level part and the jawari part of the bridge calls for work of skilled craftsmanship.
The tuning pegs, made of wood to wind and hold the strings. They are crucial to sitar as all tuning is done by turning (rotating) the khuntis. These are made of wood. These days some sitar makers use steel pegs in sitar (as used in guitar), which help in tuning sitar comfortably and accurately and without hazard of snapping.
Convex shaped metallic rods tied on the dand or Fingerboard. They are 17 to 23 in number, but should not be less than 17 in number. They are movable so as to provide certain flat notes. Certain ragas demand pure or flat notes have to be on their one higher or lower shrutis. Movability of frets in sitar supports that.
A tying string made of Polyvinyl used to tie frets to the dand or the wooden Fingerboard.
A strip made of animal bone each has small holes and is affixed to the end part of the Dand or fretboard. The holes in ‘Taar Gahan’ help strings to pass through them, rendering vibrations to happen.
Meru or Atti
A strip of animal bone or Ebony which has cuts on it. It is placed parallel to ‘Taar Gahan’. Strings from Taar Gahan holes pass through the cuts towards the upper pegs or khuntis. They are specially made of animal bone because if the strip is made of wood the strings may make a deep mark which may have a bad effect on the vibrations rendering the sound to dampen.
These allow minor adjustments, which need to be made without having to go to the large tuning pegs. They are threaded in the strings of the sitar especially in the Baaj and Jod strings.
This is the tail piece attached to the posterior end of the sitar on Toomba. There are mainly 3 nails or keel affixed on langot or the tail piece, made of animal bone on which the strings are tied.
Before the chikari string reaches khunti it has to pass through a tiny pillar shaped structure made of animal bone.
Before the chikari string reaches khunti it has to pass through a tiny pillar shaped structure made of animal bone called mogra.
Tarab ka mogrA
They are the dandis protective grommets for the sympathetic strings.
There are mainly two schools or styles of sitar playing. Keeping that in view Sitars are crafted accordingly. Both schools differ in their main strings.
The main strings are those which run above the curved threats to stop these things are placed on the big bridge or Bada Ghoraj, and the Tarab/Sympathetic strings can be 12-13 in number. Run under the frets and are placed on the small Bridge or Chhota Ghoraj. Their purpose is only to serve as resonators to the note which is played on on the main string. So they are tuned to the notes according to a particular melody or Raga.
You may buy the Gandhar Pancham strings here and the Kharaj Pancham strings here.
This style of sitar has 7 main strings.
- Pancham Chikari
- Chotti Chikari
- Badi Chikari
GANDHAR PANCHAM SITAR
This style of sitar has 6 main strings.
- Steel string(Tuned to third major or minor as per the the tonic or the keynote is determined)
- Steel Pancham Chikari
- Chotti Chikari
- Badi chikari